Thursday, 19 November 2026

Repairing Champagne’s Bow — What We Did and What We Learned

 


Repairing Champagne’s Bow — What We Did and What We Learned

The Winter Boat Shed | Philip Russell, PMR Sailing

What were a set of divers’ weights doing on the foredeck of a Thames A-Rater? Paul and I had found water beneath the teak on Champagne. We could get adhesive into the gap. The puzzle was how to hold the wood against the curve of the boat while it set. That was where the diving equipment came in.

We were pleased with the result when the weights came off. Some time later, cabinet maker and Rater restorer Richard Stent removed the jib fittings and got a view of the deck that Paul and I had never had. If I were putting together a photograph album of this job, that is the picture I would want alongside the one of our weights. Between them, they tell the story.

Where the teak had lifted

Although I think of this as the bow repair, the loose wood we first worked on was back towards the cockpit, under and around the rails that guide the jib sheets. Those are the lines we use to control the jib. On a sailing day I look along those rails to see where a sheet leads. This time it was the edge of the teak beside them that mattered.

Water had got between the layers, and part of the teak laminate had lifted. We could see the separation where the edge was exposed. The rail interrupted our view. Looking back, I would mark both ends of the visible gap on a photograph and leave a question mark where the wood disappeared beneath the fitting. It would be a more useful record for the next person taking the boat apart.



The most useful pieces of wood were the ones we cut to shape

Paul and I slipped a knife beneath the edge that had already lifted. That gave us just enough access to introduce waterproof adhesive between the layers. Then we had to persuade the teak to sit back where it belonged.

Imagine laying a straight piece of timber across a curved deck. Depending on where it touches, you can put considerable weight on it and still leave the bit you care about standing proud. We cut pieces of wood to fit the shape of Champagne’s bow and laid them over the repair. Across those went a much larger, heavy piece of timber. The divers’ weights went on top.

Each piece had a job. The shaped wood followed the local curve, the large timber bore down on those pieces, and the weights kept the whole arrangement pressing down while the adhesive set. The divers’ weights make the better photograph, but if I had to explain the job to somebody at the club, I would pick up one of the shaped pieces first.

Once we took everything off, the teak we had reached stayed down and appeared well bonded. That was the result we could see. Our account gives no adhesive specification, curing time or measured load, and the condition beneath the fittings was still an open question. Those details matter if someone is considering work on a different boat.

What Richard found under a jib fitting

When Richard took over, he removed the jib fittings. Beneath one of them he found another area where the wood had delaminated. With the fitting out of the way he could reach the separated layers. He repeated the local bonding process there and brought that wood back together too.

I was glad we had done our part, and equally glad Richard had taken the fittings off. Both observations belong in the maintenance record. The teak Paul and I bonded had stayed down. There was also loose wood under a fitting. Our first inspection could only ever have recorded the first part of that story.

One question I would carry forward is exactly where the water entered. Finding water near a rail tells us where it ended up. On a future inspection I would want a close look at the repaired edge and the area around the fastening, particularly after the deck has been wet.

Where the teak had disappeared altogether

Richard also repaired slight damage to the bow itself. Elsewhere he faced a rather different problem. In a few places someone had sanded right through the thin teak surface. It had happened before we bought Champagne. It may have happened during the build or during later work. We have no way of dating it more closely.

Think about the temptation when a patch of wood looks a different colour. A little more sanding might seem the obvious way to even it up. Here, the teak that gave the surface its colour had already gone. Richard stained the exposed patches to match the surrounding wood. Afterwards, we could no longer pick out the sanded-through areas by eye.

That is a detail worth writing down precisely because Richard did it so well. A future owner looking at the finished deck might reasonably assume there was teak of equal thickness across the lot. I would like them to have our notes before they reach for the sandpaper.

Paul’s next project is a rope bow fender

Having put the bow right, we would like to protect it when we come alongside. Paul is learning to make a traditional rope bow fender, sometimes called a bow pudding. He has never made one before. Its shape is part of the appeal for Champagne. The middle can carry the padding where the stem meets a landing stage, and the two arms can taper away along the sides.



For anyone who would like to try the ropework, here is a bench exercise based on a photographed bow-fender build. Paul’s finished dimensions and fastening arrangements are still to be decided.

  1. Take the shape off the boat. Hold a length of soft cord around the stem at the intended contact height. Mark the centre and the two ends of the padded section. Transfer the curve to cardboard. That gives you something to work against in the shed.

  2. Make the backbone and two eyes. Use flexible rope for the core. Turn a loop back at each end and bind its neck tightly with several close turns of strong twine. This binding is called a seizing. Leave both eyes clear of the area that will be padded.

  3. Build up the middle. Lay lengths of clean spare rope along the backbone. Use progressively shorter pieces towards the outside of the bundle so the greatest thickness falls at the centre mark. Bind the bundle at intervals while holding it to the template. Longer pieces along the outside of the bend help it keep its curve.

  4. Practise the cover on an offcut. With thinner cord, make a ring of evenly spaced half-hitches around a scrap core. For the next round, work a half-hitch into each loop of the preceding round. Each time, pass the working end through the loop and back through its own bight, then draw it snug. A few rounds will show whether your spacing leaves gaps or pulls the bundle into a waist.

  5. Cover the curved core and finish the ends. Start beside one eye and continue the hitching over the padding, adjusting the spacing as the girth changes. At the far end, secure the cord with a whipping and bury the tail beneath the covering. Run your hand over the face that will touch the boat to feel for a protruding end or a hard lump.

For close-ups of the core, seized eyes and half-hitched covering, see Scott B. Williams’s account of the fender Michelle made for a pulling boat. Its dimensions belong to that dinghy. Our cardboard pattern needs to come from Champagne. Making a Rope Bow Fender



The question still on the bench

How do we attach it? Two neat eyes on a fender are only half an answer. The direction of the ties matters. Imagine the bow just touching the edge of a landing stage. If the fender rolls upwards at the first touch, the beautifully padded middle ends up on deck and the freshly repaired stem is left against the timber.

My next step would be to hold a soft mock-up in place with Paul and try gentle hand pressure from ahead and from either side. We could see where it rides up, where a tie might rub the finish and whether the jib sheets still run clear. Then we could show Richard the proposed leads and ask which existing points, if any, are suitable. We have yet to choose an attachment on Champagne.

When I look at the bow now, some of the best work is the hardest to see. The teak lies down where Paul and I bonded it. Richard reached the patch hidden by the fitting, repaired the slight damage at the bow and blended away the old sanding marks. I would keep the shaped pieces of wood, too. Hand one to another sailor and the curve explains in a moment what those divers’ weights were doing on our deck.

And if you sail a Thames Rater with a removable rope bow fender, Paul and I would particularly like to see a photograph taken from above. We know what we want the front to look like. It is where those two ends go that interests us now.

No comments:

Post a Comment

Repairing Champagne’s Bow — What We Did and What We Learned

  Repairing Champagne’s Bow — What We Did and What We Learned The Winter Boat Shed | Philip Russell, PMR Sailing What were a set of divers’ ...